السبت 27 يونيو 2026
عاجل

مشكلة بالفورد والشنطة السيارة تفتح تلقائياً

ورشة السيارات
12 رد 11,998 مشاهدة 5 مشارك الأقدم أولاً
ا
الرائع2005 @user_39019 · 09-12-2010
السلام عليكم

عندي الفورد 2001 استخدام امريكي

المشكلة عند وضع القير على الدي وتحرك تفتح الشنطة تلقائياً

واحياناً

عند قفل الابواب عن طريق الريموت تفتح الشنطة

وايضا عند تامين قفل الابواب


بصراحة حيرتني تخيل تحرك تفتح الشنطة تطلع تقفلها تركب تحرك تفتح والحل تترك احد يقفلها لك
وانت بالسيارة

مالحل
A
AL8AI9ER @user_252349 · 05-02-2011
اخوي المشكلة عندك في برمجة المفتاح

اعد برمجة المفتاح وان شاء الله تزبط معاك
ا
الرائع2005 @user_39019 صاحب الموضوع · 05-02-2011
السلام عليكم

بعد معاناة قاربت 3 اشهر بين محلات المفاتيح بالخرج والغرابي يالرياض

والكل اتفق على تغير لوحات الفيوز موجوده بنفس الباب اي الباور

وسعرها بالتشليح 350ريال

تم اصلاحها ب35ريال فقط في مكة عند شارع البيبان بمحلات الزينه عند واحد حضرمي

فك الجهاز ونظفه واستغل ماشاء الله 100%

للعلم والفائدة
Y
YAKUZA @user_236458 · 16-12-2010
وعليكم السلام ورحة الله وبركاته
اخوي حاول تتأكد من سلامة الزر اللي في الباب جرب كمان تقفله بمفتاح السيارة كم يوم
+ الزر في الريموت
انا صارتلي مشكلة شبيهة في فورد 96 استغربت فجأة قامت تفتح شنطتها والابواب تفتح وتتقفل والنهاية طلعت المشكلة من الريموت فصلت بطاريته وانحلت لكن بع ما قريت عليها !!!!خوفا لا يكون شي ثاني هههههههه :bigggrin:
م
مركز جوانا @user_231566 · 16-12-2010
م
مركز جوانا
Deactivating/activating the autolock feature
Before following the procedure, make sure that the ignition is OFF and
all vehicle doors are closed.
Automatic door locks can be turned on/off with the keyless entry keypad
through the following procedure:
You must complete steps 1-5 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.
1. Enter the keyless entry keypad factory code.
2. Within 5 seconds, press and hold control 7/8.
1 2 3 4 5 6 7 8 9 0
Controls and features
91
3. Within 5 seconds (while holding down control 7/8), press and release
control 3/4.
4. Release control 7/8.
The door will lock/unlock to confirm the feature has been disabled. Once
disabled, the feature can be enabled by repeating the same sequence.
Automatic door locks can also be turned on/off through the following
procedure:
You must complete steps 1-7 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.
1. Turn the ignition key to ON.
2. Press the power door unlock control on the door panel three times.
3. Turn the ignition key from ON to OFF.
4. Press the power door unlock control three times.
5. Turn the ignition back to ON.
6. Press the unlock control once. After a five to ten second delay, the
door will lock/unlock to confirm successful programming.
7. Turn the ignition to OFF.



نفس الخطوات الي ذكرت سابقا
ا
الرائع2005 @user_39019 صاحب الموضوع · 16-12-2010
م
مركز جوانا
Deactivating/activating the autolock feature
Before following the procedure, make sure that the ignition is OFF and
all vehicle doors are closed.
Automatic door locks can be turned on/off with the keyless entry keypad
through the following procedure:
You must complete steps 1-5 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.
1. Enter the keyless entry keypad factory code.
2. Within 5 seconds, press and hold control 7/8.
1 2 3 4 5 6 7 8 9 0
Controls and features
91
3. Within 5 seconds (while holding down control 7/8), press and release
control 3/4.
4. Release control 7/8.
The door will lock/unlock to confirm the feature has been disabled. Once
disabled, the feature can be enabled by repeating the same sequence.
Automatic door locks can also be turned on/off through the following
procedure:
You must complete steps 1-7 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.
1. Turn the ignition key to ON.
2. Press the power door unlock control on the door panel three times.
3. Turn the ignition key from ON to OFF.
4. Press the power door unlock control three times.
5. Turn the ignition back to ON.
6. Press the unlock control once. After a five to ten second delay, the
door will lock/unlock to confirm successful programming.
7. Turn the ignition to OFF.





ما فهمت شئ

ترجمة من الإنجليزية إلى العربية
تعطيل / تفعيل ميزة القفل الآلي
قبل اتباع هذا الإجراء ، تأكد من أن الإشعال هو خارج و
يتم إغلاق جميع أبواب السيارة.
يمكن تشغيل اقفال باب التلقائية على / قبالة مع دخول بدون مفتاح لوحة المفاتيح
من خلال الإجراء التالي :
يجب إكمال الخطوات 1-5 في غضون 30 ثانية أو أن الإجراء
أن يتكرر لديك. إذا كان الإجراء يحتاج إلى تكرار ، يجب عليك
انتظر 30 ثانية.
1. دخول بدون مفتاح رمز دخول مصنع لوحة المفاتيح.
2. في غضون 5 ثوان ، الصحافة وتسيطر 7 / 8.
1 2 3 4 5 6 7 8 9 0
الضوابط وميزات
91
3. في غضون 5 ثوان (أثناء الضغط باستمرار السيطرة 7 / 8) ، والافراج عن الصحفية
السيطرة 3 / 4.
4. الافراج عن السيطرة 7 / 8.
وسيكون باب قفل / فتح لتأكيد تم تعطيل ميزة. مرة واحدة
المعوقين ، يمكن تمكين ميزة بتكرار نفس تسلسل.
ويمكن أيضا اقفال باب التلقائية يتم تشغيل / إيقاف من خلال ما يلي
الإجراء :
يجب إكمال الخطوات 1-7 في غضون 30 ثانية أو أن الإجراء
أن يتكرر لديك. إذا كان الإجراء يحتاج إلى تكرار ، يجب عليك
انتظر 30 ثانية.
1. تحويل الى مفتاح التشغيل على.
2. اضغط على باب السلطة فتح السيطرة على لوحة الباب ثلاث مرات.
3. بدوره على مفتاح الإشعال من الدخول إلى خارج.
4. اضغط على باب فتح سيطرة السلطة ثلاث مرات.
5. تحويل الاشتعال مرة أخرى إلى تشغيل.
6. اضغط على فتح التحكم مرة واحدة. بعد تأخير الثاني 09:55 ، و
والباب قفل / فتح لتأكيد برمجة ناجحة.
7. بدوره الإشعال إلى خارج.
__________________
ا
الرائع2005 @user_39019 صاحب الموضوع · 16-12-2010
م
مركز جوانا
حيااك الله اخي
عذرا ع التاخير
لو سمحت اذكر نوع السياره لتفاصيل ادق
اي بمعنى كروان فكتوريا اومركيز وغيرها
راح احاول ارسل لك حق الفكتوريا وجرب
اذا مانفع ارسل نوع السياره


السيارة / فورد جراند ماركيز

موديل/ 2001

الاستخدام امريكي



بانتظارك اخوي
م
مركز جوانا @user_231566 · 13-12-2010
Deactivating/activating the autolock feature
Before following the procedure, make sure that the ignition is OFF and
all vehicle doors are closed.
Automatic door locks can be turned on/off with the keyless entry keypad
through the following procedure:
You must complete steps 1-5 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.
1. Enter the keyless entry keypad factory code.
2. Within 5 seconds, press and hold control 7/8.
1 2 3 4 5 6 7 8 9 0
Controls and features
91
3. Within 5 seconds (while holding down control 7/8), press and release
control 3/4.
4. Release control 7/8.
The door will lock/unlock to confirm the feature has been disabled. Once
disabled, the feature can be enabled by repeating the same sequence.
Automatic door locks can also be turned on/off through the following
procedure:
You must complete steps 1-7 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.
1. Turn the ignition key to ON.
2. Press the power door unlock control on the door panel three times.
3. Turn the ignition key from ON to OFF.
4. Press the power door unlock control three times.
5. Turn the ignition back to ON.
6. Press the unlock control once. After a five to ten second delay, the
door will lock/unlock to confirm successful programming.
7. Turn the ignition to OFF.
م
مركز جوانا @user_231566 · 13-12-2010
حيااك الله اخي
عذرا ع التاخير
لو سمحت اذكر نوع السياره لتفاصيل ادق
اي بمعنى كروان فكتوريا اومركيز وغيرها
راح احاول ارسل لك حق الفكتوريا وجرب
اذا مانفع ارسل نوع السياره
ا
الرائع2005 @user_39019 صاحب الموضوع · 11-12-2010
م
مركز جوانا
حيااك اخي
الغي فتح الابواب مع التعشيق
باعادة البرمجه يدويا
هل عندك الرقم السري للابواب؟؟
اذا صعب عليك شي شرفنا ونحلها لك بحول الله
بالتووووفيق




الله يغنيك اخوي

يا ليت طريقة الغاء فتح الابواب مع التعشيق والرقم موجود عندي

وللعلم انا دائما كل صباح استخدم فتح الابواب عن طريق الارقام السريه

وجزاءك الله خير

بانتظاركـ
م
مركز جوانا @user_231566 · 11-12-2010
حيااك اخي
الغي فتح الابواب مع التعشيق
باعادة البرمجه يدويا
هل عندك الرقم السري للابواب؟؟
اذا صعب عليك شي شرفنا ونحلها لك بحول الله
بالتووووفيق
ا
الرائع2005 @user_39019 صاحب الموضوع · 10-12-2010
M
M~أمير بكلمتي~M
وعليكم السلام ورحمة الله وبركاته

حاول تتأكد من سلامة زر الشنطه الي في الباب ممكن يكون فيه مشكلة التماس او شئ

أخوكـ


هلا اخوي

الزر سليم

والمشكلة ارقهتني
M
M~أمير بكلمتي~M @user_58367 · 09-12-2010
وعليكم السلام ورحمة الله وبركاته

حاول تتأكد من سلامة زر الشنطه الي في الباب ممكن يكون فيه مشكلة التماس او شئ

أخوكـ
سجّل دخول للرد...